Start With the Function of the Edge
Edging is asked to do one of three jobs: separate two surface materials, retain a raised bed or terrace, or act as a visual feature. The job determines every other choice. A boundary between lawn and gravel carries almost no lateral load, so a thin strip with stakes is enough. A bed raised 200 mm above the surrounding ground carries soil pressure that will bow a light section, so thickness and stake spacing must increase. A feature edge that runs through a paving scheme has to be dimensionally accurate and resist impact from maintenance equipment.
Write down the retained height, the expected load and the finished visual intent before looking at a catalogue. Most specification errors in landscape edging come from choosing the section by appearance and then discovering that it deforms under the load it is asked to hold.
Thickness, Height and Section Form
Weathering steel edging is supplied from about 1.5 mm to 3 mm thick, in heights from 100 mm to 300 mm. A practical rule is to use 1.5 mm to 2 mm strip for surface separation, and 3 mm or heavier for any edge that retains soil, borders a driveway or sits in a public space.
| Application | Suggested thickness | Suggested height |
|---|---|---|
| Lawn and gravel separation | 1.5 mm | 100 mm |
| Planting bed border | 2 mm | 150 mm |
| Raised bed or terrace edge | 3 mm | 200 mm to 300 mm |
| Path, driveway or public realm | 3 mm or heavier | 150 mm to 250 mm |
Section form matters as much as thickness. A folded top edge stiffens the strip and removes the sharp cut edge from view. A folded gravel flange locks surface material behind the steel and prevents migration. Cleats or pre-punched stake pockets speed up installation on site and keep the stakes vertical.
Steel Grade and Corrosion Performance
The correct substrate is an atmospheric corrosion resistant steel, not ordinary carbon steel. Grades in common use are ASTM A606 Type 4 for thin strip, ASTM A588/A588M where higher strength sections are wanted, and EN 10025-5 grades such as S355J2W for European projects. These deliver minimum yield strengths around 345 MPa and contain the copper, chromium and nickel additions that let a compact patina form.
Two practical points follow from the grade choice. First, plain carbon steel edging will corrode through at the soil line in a few years and should not be accepted as an equivalent. Second, the higher-phosphorus variants of EN 10025-5 form patina faster but are less tolerant of welding, which matters if the edging is welded into frames rather than simply driven into the ground.
Site Conditions: Soil, Water and Climate
Weathering steel needs alternating wet and dry conditions to build a stable patina. Above ground and freely draining, it performs well. Buried in permanently wet, acidic or clay-heavy soil, the steel corrodes much faster, and the buried zone is always the first part to suffer. Where soil is acidic, adding a gravel drainage layer or a membrane behind and below the strip noticeably extends service life.
Climate sets the pace of appearance change as well as the corrosion rate. In dry inland conditions the patina darkens slowly and stays even. In coastal or high-rainfall locations the patina forms quickly at first but may never compact fully, and runoff staining of adjacent paving is more pronounced. Irrigation heads should not be aimed directly at the steel, since continuous wetting keeps the buried zone saturated and leaves mineral deposits on the surface.
Supply Format, Fabrication and Quality Checks
Edging is normally ordered as fixed-length strip, in 1 m to 6 m sections, cut to plan, with pre-drilled stake holes or supplied with matching stakes. Buyers running a landscape business usually want consistent section lengths, a stable thickness tolerance and the ability to order repeat quantities without a colour change, which is why the surface condition at despatch should be agreed in writing.
Before release, check three things. Thickness should be measured against the order, since a lighter gauge deforms quickly. Flatness and straightness matter because a bowed section will not hold a line. And the material should arrive with an EN 10204 type 3.1 certificate recording heat analysis and mechanical results, so the weathering chemistry can be verified rather than assumed. Powder-coated or galvanized substitutes are not weathering steel and should be rejected where a bare patina is specified.
Frequently Asked Questions
Q: What thickness should I choose for garden edging?
A: 1.5 mm to 2 mm for surface separation and bed borders, and 3 mm or more where the edge retains soil or takes impacts.
Q: Which steel grade is correct?
A: A weathering grade such as ASTM A606 Type 4, ASTM A588/A588M or EN 10025-5 S355J2W. Plain carbon steel is not an acceptable substitute.
Q: How deep should the strip be set?
A: Excavate about 100 mm, leaving roughly 30 mm to 50 mm of strip above the finished soil line, and backfill both sides.
Q: Does soil type affect performance?
A: Yes. Acidic, waterlogged and heavy clay soils accelerate corrosion at the buried zone, so a gravel layer or membrane is recommended.
Q: Can sections be joined on a curve?
A: Gentle curves are formed by hand on thin strip, while tight radii use short segments cut and set to follow the sweep.
Q: What documents should come with the delivery?
A: An EN 10204 type 3.1 certificate with heat analysis and mechanical results, plus thickness and straightness records against the order.







