What A709 Gr50W Covers
ASTM A709/A709M is the specification for structural steel for bridges, covering carbon, high strength low alloy, weathering and quenched-and-tempered grades. Grade 50W is the weathering variant, where the W suffix indicates improved atmospheric corrosion resistance, and the 50 refers to a minimum yield strength of 50 ksi, equivalent to 345 MPa. It exists because bridge structures are exposed to weather and de-icing salt, and unpainted weathering steel can eliminate the recurring cost of repainting over a long design life.
Because the material has to perform under traffic loading, impact requirements, toughness and weldability are controlled more tightly than in general structural grades, and A709 grades are frequently ordered with supplementary impact testing to suit the project's minimum service temperature.
Type A, Type B and Type C
A709 Grade 50W is supplied in three types, and the type is defined by chemical composition rather than by strength. Type A corresponds to ASTM A588/A588M Grade A, Type B to Grade B, and Type C to Grade C. In practice this means a plate ordered as A709 Gr50W Type A and a plate ordered as A588 GrA with the same thickness are chemically and mechanically equivalent, and bridge fabricators treat them as interchangeable subject to the governing project specification.
Type A is the most commonly stocked of the three, and it is the type most often specified for plate girders, parapets and other fabricated bridge components. The differences between the types lie mainly in the ranges of copper, chromium, nickel, silicon and phosphorus, which affect both the pace of patina formation and weldability. A project that specifies one type should not receive another without written approval, even though the strength values are the same.
Chemistry and Mechanical Comparison
The table below shows the limit values in mass percent for the two designations that are most often compared on a project drawing.
| Standard | Grade | C max | Mn | P max | S max | Si | Cr | Ni max | Cu | V |
|---|---|---|---|---|---|---|---|---|---|---|
| ASTM A709/A709M | A709 Gr50W Type A | 0.19 | 0.80-1.25 | 0.04 | 0.05 | 0.30-0.65 | 0.40-0.65 | 0.40 | 0.25-0.40 | 0.02-0.10 |
| ASTM A588/A588M | A588 GrA | 0.19 | 0.80-1.25 | 0.04 | 0.05 | 0.30-0.65 | 0.40-0.65 | 0.40 | 0.25-0.40 | 0.02-0.10 |
| Standard | Grade | Thickness | Yield strength | Tensile strength |
|---|---|---|---|---|
| ASTM A709/A709M | A709 Gr50W | Up to 100 mm | 345 MPa minimum | 485 MPa minimum |
| ASTM A588/A588M | A588 GrA | Up to 100 mm | 345 MPa minimum | 485 MPa minimum |
Because the two rows match on both chemistry and strength, the corrosion resistance and structural performance delivered by either designation are the same, provided the type or grade is the one specified and the thickness is within the qualified range.
Stock Formats and Fabrication for Bridge Work
Plate is normally stocked from 3 mm to 150 mm, and the grade is also produced and held as rolled sections so that a bridge package can be sourced from one supply chain. Typical stock formats include H-beams in A588 GrA, H-beams together with angle bars, flat bars and square hollow sections in A588 GrB, and rectangular hollow sections in A588 GrA. These formats cover girders, bracing, connection plates and secondary members.
Fabrication follows bridge practice. Welding procedures are qualified to the governing standard, low-hydrogen consumables are used for thick and restrained joints, and heat input is controlled to protect both toughness and the alloy chemistry that drives patina formation. Bolted connections use high strength fasteners of matching class with galvanically compatible washers, and any direct junction with galvanized or aluminium components is isolated to prevent bimetallic corrosion. Plate edges exposed to weather should be dressed and free of laminations so that water does not collect in a defect and promote local attack.
Specifying Equivalent Material and Verification
Substitution between A709 Gr50W and A588 is accepted on many projects, but it must be confirmed by the engineer of record, because some specifications additionally require Charpy impact testing at a defined service temperature, ultrasonic inspection of plate, or restrictions on the phosphorus range of the type supplied. Where the plate will be used bare, the atmosphere also has to be suitable: patina formation needs alternating wet and dry cycles, so weathering plate is not appropriate for continuously wet locations, buried zones or chloride-heavy marine spray zones without additional protection.
Verification at delivery should cover the heat number against the certificate, chemistry including copper, chromium and nickel, tensile and impact results, thickness and flatness tolerances, and surface quality before despatch. Certificates issued to EN 10204 type 3.1 with chemical composition included are the practical way to confirm that the weathering performance specified on the drawing has actually been delivered.
Frequently Asked Questions
Q: Is A709 Gr50W the same as A588?
A: A709 Gr50W Type A is chemically and mechanically identical to A588 Grade A. Types B and C correspond to the other A588 grades.
Q: What is the yield strength of A709 Gr50W?
A: 345 MPa minimum, with a minimum tensile strength of 485 MPa for thicknesses up to 100 mm.
Q: Can the two grades be substituted freely?
A: Only with the engineer's approval, since impact requirements, inspection class and type-specific chemistry may differ between projects.
Q: What plate thickness is available?
A: Commonly 3 mm to 150 mm, with matching H-beams, angles, flat bars and hollow sections in stock formats.
Q: Does bridge weathering plate need painting?
A: In a well-ventilated atmosphere with wet and dry cycling it is used bare, which is the main economic advantage of the grade.
Q: What must be verified on delivery?
A: Heat number traceability, full chemistry including copper, chromium and nickel, tensile and impact results, plus thickness and surface inspection records.







