SPA-C Thickness: Impact on Cold Forming & Max Cold Bending Thickness?

Dec 29, 2025 Leave a message

For customers using SPA-C Corten Steel (JIS G 3125 standard) in cold forming processes (e.g., bending, stamping), understanding how thickness affects forming performance and the maximum allowable cold bending thickness is critical to avoid cracking. The core conclusion is: Thickness negatively correlates with cold formability; max allowable cold bending thickness is 8mm under general conditions. This article clarifies the impact rules, standard requirements, and practical operation guidelines.

 

How long does it take for the patina layer of weathering steel to fully mature?

 

1. How Thickness Affects Cold Forming Performance of SPA-C

SPA-C's cold formability (ductility, bendability) decreases as thickness increases, mainly due to two factors:

Residual Stress & Deformation Resistance: Thicker SPA-C sheets have higher internal residual stress from the hot-rolling process. During cold forming, greater external force is required to cause plastic deformation, increasing the risk of edge cracking or internal microcracks. For example, 3mm-thick SPA-C bends easily with a small radius, while 10mm-thick sheets are prone to edge splitting without proper process control.

Uniformity of Alloy Distribution: Thicker sheets may have slight unevenness in Cu-Cr-P alloy distribution, leading to local ductility differences. During cold forming, stress concentrates in low-ductility areas, resulting in uneven deformation and potential cracking.

Practical performance trend: Sheets ≤6mm have excellent cold formability; 6-8mm require moderate process adjustment; >8mm have significantly reduced formability, requiring strict parameter control or pre-treatment.

 

Which is more moisture-resistant, weathering steel or galvanized steel?

 

2. Maximum Allowable Thickness for Cold Bending of SPA-C

Based on JIS G 3125 standard and industrial practice, the maximum allowable cold bending thickness of SPA-C is determined by the bending radius (inner radius, R):

General Cold Bending (R ≥ 3×thickness): Maximum allowable thickness is8mm. This is the most common scenario (e.g., architectural decorative bends, structural brackets). At this thickness and radius, SPA-C's ductility (elongation ≥21% per JIS G 3125) ensures crack-free forming.

Small-Radius Bending (R = 1.5-2×thickness): Maximum allowable thickness is reduced to 6mm. Smaller bending radii increase deformation severity; thicker sheets (>6mm) will experience excessive stress, leading to visible cracks on the outer bend surface.

Thickness >8mm: Cold bending is not recommended. If cold forming is unavoidable (e.g., special structural needs), the maximum thickness should not exceed 10mm, and pre-heating (≤150℃, non-hot forming) is required to improve ductility. However, this increases process complexity and quality risk.

 

How to prevent cracking in weathering steel during welding?

 

3. Practical Cold Forming Recommendations

Thickness ≤6mm: No special adjustments needed. Use standard cold bending equipment; adopt R ≥ 2×thickness for better surface quality. No pre/post-treatment required.

Thickness 6-8mm: ① Increase bending radius to R ≥ 3×thickness; ② Use slow forming speed (2-3mm/s) to reduce stress concentration; ③ Grind sheet edges to remove burrs (sharp edges are prone to cracking); ④ Conduct post-bending inspection with a penetrant test (PT) to check for hidden cracks.

Thickness >8mm: Avoid cold bending. Opt for hot forming (200-300℃) or replace with thinner sheets welded into the required thickness, which is more cost-effective and reliable than high-risk cold forming.

 

What are the mechanical properties of annealed SPA-H steel plates?

 

In summary, SPA-C's cold formability decreases with increasing thickness, with a maximum allowable cold bending thickness of 8mm for general scenarios. Selecting the right thickness and optimizing bending parameters ensures crack-free cold forming, maintaining SPA-C's mechanical and weather-resistant properties.