09CrCuSb (ND Steel) Seamless Steel Tube for Sulfuric Acid Dew Point Corrosion Resistance

Oct 13, 2025 Leave a message

What 09CrCuSb (ND Steel) Is

09CrCuSb, generally known as ND steel or 09 chromium copper antimony steel, is a low-alloy steel developed specifically to resist sulfuric acid dew point corrosion. It is supplied as seamless steel tube, plate, forging and matching welding consumables. The steelmaking route is built around cleanliness: ultra-high-power electric furnace melting followed by secondary refining and vacuum degassing, which keeps oxygen and residual elements low and stabilises the alloy additions that drive corrosion resistance.

In a corrosive flue gas environment the surface of the tube develops a dense, stable passivation film enriched with Cr, Cu, Sb and Ti. That film grows as several enriched zones and is considerably denser and more uniform than the oxide layer formed on ordinary carbon steels, which is why the material performs far better where condensed sulfuric acid attacks metal.

Compared with conventional steels such as carbon steel and copper-bearing weathering steel, ND steel combines better sulfuric acid dew point corrosion resistance with sufficient mechanical strength for pressure-part fabrication.

Chemical Composition of 09CrCuSb

The table below gives the product analysis limits normally applied to 09CrCuSb seamless tube, aligned with the values listed for the grade in the Chinese pressure vessel standard GB 150.2-2011.

Element C Si Mn Cr Cu Sb P S
09CrCuSb ≤0.12 0.20-0.40 0.35-0.65 0.70-1.10 0.25-0.45 0.04-0.10 ≤0.030 ≤0.020

Older supplier datasheets for the same grade often quote a wider chromium window up to 1.20% and a single upper limit of 0.10% for antimony. Where a specification refers to GB 150.2-2011, the narrower chromium range of 0.70-1.10% and the antimony range of 0.04-0.10% govern, and the phosphorus and sulfur ceilings of 0.030% and 0.020% apply. Chromium and copper build the passive film; antimony refines its structure and is the element that most clearly separates ND steel from ordinary copper-bearing steel.

Mechanical Properties of 09CrCuSb Tube

Seamless tube in 09CrCuSb is delivered with the strength and ductility level below. Values are for the delivered tube product and are checked on tensile test pieces taken in the longitudinal direction.

Grade Tensile strength (MPa) Yield strength (MPa) Elongation (%)
09CrCuSb 390-550 ≥245 ≥25

The combination of a moderate yield level and elongation above 25% keeps the tube formable for bending, expanding and rolling into economizer and air preheater elements, while the tensile range leaves sufficient margin for tube-to-tubesheet joint strength.

Why ND Steel Resists Sulfuric Acid Dew Point Corrosion

In coal-fired boilers and oil-fired process heaters the flue gas temperature commonly falls between 90 °C and 160 °C. This is exactly the window in which sulfuric acid vapour condenses on metal surfaces, and it is the reason heat recovery equipment suffers heavy metal loss, pitting and eventual perforation. ND steel is designed for that window rather than for general atmospheric exposure.

Laboratory corrosion data taken in a 70 °C, 50% sulfuric acid solution show that the uniform corrosion resistance of ND steel is approximately ten times that of 20g mild steel, about three times that of 304 stainless steel and roughly 1.5 times that of CR1A steel. The advantage over austenitic stainless steel is important in practice, because 304 is vulnerable to dilute sulfuric acid attack at these temperatures while ND steel remains stable.

Typical Applications of 09CrCuSb Seamless Tube

ND steel is regarded as one of the most suitable materials for sulfuric acid low-temperature dew point corrosion service, and its seamless tube is used in the following equipment:

Economizers and boiler tail-end heat recovery banks in coal-fired and oil-fired power plants

Air preheaters, including tubular and rotary designs, in refineries and petrochemical plants

Heat exchangers and condensers handling flue gas with high sulfur content

Evaporators and gas coolers in sulfuric acid and metallurgical process lines

Flue gas treatment components in waste incineration and metallurgy plants, where SO₂ and H₂SO₄ vapours are present

Field experience with these components shows that equipment built from ND steel can achieve an operating life three to five times longer than comparable carbon steel equipment and can cut maintenance frequency by more than 40%. For plant operators this translates into fewer unplanned outages, lower replacement cost and a shorter payback on the higher initial material cost.

Frequently Asked Questions

Q: What does the name 09CrCuSb mean?
The designation indicates the alloying concept: a low-carbon steel (09, meaning nominal carbon below 0.10-0.12%) with chromium, copper and antimony additions. It is also widely called ND steel, short for the corrosion-resistant grade originally developed for sulfuric acid dew point service.

Q: Can 09CrCuSb tube be welded with matching consumables?
Yes. The grade is supplied with dedicated welding consumables matched to its composition and strength level, which keeps weld metal corrosion resistance close to that of the parent tube in flue gas service.

Q: How does ND steel compare with ordinary weathering steel?
Weathering steel such as A588 or Q355NH is designed for atmospheric exposure. ND steel targets condensed sulfuric acid at 90-160 °C inside flue gas ducts, which is a far more aggressive chemical environment, so the two grades are not interchangeable.

Q: Which flue gas temperature range is most critical?
The most severe range is broadly 90 °C to 160 °C, where acid condensation is at its peak. Below the water dew point the condensate becomes more dilute, and above the acid dew point the tube wall stays dry, so both cases are less damaging than the intermediate window.

Q: What tube sizes are normally produced?
Seamless tube in 09CrCuSb is produced over the wall thickness and outside diameter ranges used by economizer and air preheater designers, including small-diameter, thin-wall elements, and is inspected to the ordered specification for pressure-part service.

Q: Is the grade suitable for sour or chloride-rich service?
The grade is optimised for sulfuric acid dew point corrosion in combustion flue gas. For chloride-dominated or wet sour service, material selection must be reviewed against the specific chemistry, because the passive film chemistry of ND steel is tuned to acid sulfate condensation rather than to chloride pitting.