What Q295GNH Corten Steel Plate Is
Q295GNH is a hot-rolled weathering steel plate defined in GB/T 4171, the Chinese standard for high strength low alloy structural steels with improved atmospheric corrosion resistance. The designation records a minimum yield strength of 295 MPa, and the GNH suffix identifies the high weathering class of the standard, intended for welded structures exposed to the atmosphere for long periods.
The plate is normally delivered bare, without coating, and is used where a self-protecting rust layer can replace paint. Typical plate thickness runs from 6 to 50 mm for structural work, and heavier plates up to 150 mm are available for large welded assemblies.
Chemical Composition and Mechanical Properties
The tables below give the chemical composition and the tensile requirements for the grade as supplied under GB/T 4171.
| Element | Q295GNH, % |
|---|---|
| Carbon (C), max | 0.15 |
| Silicon (Si) | 0.10–0.50 |
| Manganese (Mn) | 0.30–1.00 |
| Phosphorus (P), max | 0.03 |
| Sulfur (S), max | 0.03 |
| Copper (Cu) | 0.25–0.55 |
| Chromium (Cr) | 0.40–0.80 |
| Nickel (Ni), max | 0.65 |
| Property | Q295GNH |
|---|---|
| Yield strength, min | 295 MPa |
| Tensile strength | 430–560 MPa |
| Elongation, min | 22% |
| Impact energy at room temperature, min | 27 J |
| Tensile range for delivery state | Yield 255–295 MPa |
Copper, chromium and nickel are the elements that produce the protective oxide layer, while the modest carbon and sulfur limits keep the plate weldable and tough. The strength-to-weight ratio allows designers to work with thinner sections than a plain carbon steel solution would need for the same load.
Processing and Fabrication Features
Weldability: the plate can be joined by shielded metal arc, gas metal arc, gas tungsten arc and submerged arc welding, with heat-affected zone impact energy of at least 20 J so that welded joints retain toughness.
Cutting: plates of 6–50 mm are cut by plasma or laser processes with clean edges and limited heat distortion.
Forming: cold bending is carried out with an inner bend radius of at least 1.5 times the plate thickness, and stamping elongation of at least 20% supports pressed components.
Hardness and wear: typical Brinell hardness of HB 140–160 gives good resistance to abrasion in transport and container duty.
Temperature service: short-term exposure to 300–400 °C is acceptable, while continuous operating temperature is normally limited to 200 °C.
Fatigue: the fatigue limit under cyclic loading is around 0.4 times the tensile strength, which suits dynamically loaded frames and chassis parts.
Corrosion Resistance and Life-Cycle Value
After a short weathering period, Q295GNH develops a dense and stable oxide film that limits the access of oxygen, moisture and airborne pollutants to the base metal. Where the surface dries regularly, that film becomes the finished surface and no paint system is required, so repainting cycles and the associated access costs disappear.
The practical benefits are a material saving of roughly 10 to 30% compared with a conventional carbon steel design, lower maintenance spending over the ownership period, and a service life that commonly exceeds 30 years in ordinary outdoor exposures. In mixed industrial and rural atmospheres these gains are largest, while buried, permanently wet or heavily chloride-loaded conditions still call for additional protection.
Typical Applications
Because the grade combines strength, toughness and weathering resistance, it is used for railway wagons and freight containers, truck frames and bodies, transmission towers, bridge components, port and terminal structures, oil platform modules, and chemical and petroleum equipment exposed to corrosive media.
It is also specified for architectural and landscape work where the patina is part of the design intent, including facades, screens, planters and public furniture that must stay maintenance-free for decades.
FAQ
Q: What does Q295GNH mean?
Q295 records a minimum yield strength of 295 MPa, and GNH identifies the high atmospheric corrosion resistance class of GB/T 4171.
Q: What is the tensile strength of Q295GNH plate?
Tensile strength ranges from 430 to 560 MPa, with minimum yield strength of 295 MPa.
Q: Does Q295GNH plate need painting?
No. In exposed outdoor service the plate forms its own protective oxide layer, which is normally left as the finished surface.
Q: Can Q295GNH be welded?
Yes, it welds with conventional arc processes, and the heat-affected zone retains an impact energy of at least 20 J.
Q: What thicknesses are available?
Structural plates of 6–50 mm are standard, with thicknesses up to 150 mm available for heavy welded structures.
Q: Where should Q295GNH not be used bare?
In buried, permanently wet or high-chloride locations, where the protective layer cannot dry and stabilise.







